1P Hydraulic Gear nfuli

EZI EGO

Nfuli gia mpụga bụ nfuli ndị kachasị ewu ewu nke eji na usoro hydraulic nke oge a.

Ihe omuma ha bu otutu, ike na ndu bara uru.

The mfe ewu ana achi achi mmachi zuo akwụ ụgwọ na-arụ ọrụ. Ekele dịrị echiche dị iche iche, yana imeziwanye atụmatụ ngwaahịa na njirimara, nyocha dabere na ọtụtụ afọ nke ahụmịhe, nzi ezi na nhọrọ ihe, imepụta usoro soro n'ụzọ zuru ezu na ule na akụkụ ndị mepụtara, nfuli gia anyị eruola n'elu ụkpụrụ mma.

N'ihi nke a, ngwaahịa anyị nwere ike ịrụ ọrụ n'okpuru ọnọdụ ọrụ dị arọ ma nyefee ike hydraulic dị elu. Ọzọkwa, nfuli SJ-TECHNOLOGY na-egosipụta ezigbo hydraulic, arụmọrụ na arụmọrụ nke ọma, ụda mkpọtụ dị ala na, nke ikpeazụ ma ọ dịghị ihe ọzọ, kọmpat.

SJ Technology gia nfuli n'ihu mepụtara ya nso nke ngwaahịa na a ọhụrụ usoro nfuli aha ya bụ GPM ebe otu aha 1P, 1A, GPM0.0, GPM1.0, GPM2.0, GPM2.6, GPM3.0 adabara maka ọtụtụ ngwa dị iche iche na ụlọ ọrụ mmepụta ihe, mkpanaka, ọrụ ụgbọ mmiri na nke aerospace.

N'ozuzu, nfuli gia ndị a, na-enwekarị otu gia nke osisi aluminom abụọ na-akwado, ahụ, ihe mkpuchi nchekwa na mkpuchi. Ogwe nke ihe na-anya ụgbọ ala na-egosi ihe karịrị flange ahụ na-etinye mgbanaka mgbaaka ejima (ọnụ dị n'ime bụ akara na mpụta bụ akara uzuzu). Ihe mgbanaka na-agbanwe mgbanaka na-echedo mgbanaka ahụ. Ahụ nke mgbapụta ahụ bụ nke alloy alloy pụrụ iche na-eguzogide ọgwụ enwetara site na usoro extrusion, ebe a na-eme flange na mkpuchi site na spheroidal cast iron, nke a iji hụ na nrụrụ pere mpe ọbụlagodi mgbe enwere nrụgide dị elu, ma ọ ga na-aga n'ihu ma ọ bụ na-agafe ma ọ bụ nrụgide kachasị elu.

Gears bụ nke ígwè pụrụ iche. Ha n'ichepụta usoro ala na mma okokụre nwere a elu ogo elu hụ ala pulsation levers na ala mkpọtụ levers n'oge mgbapụta ọrụ.

Bushings na-mere nke pụrụ iche ala-esemokwu na hi-eguzogide aluminum alloy na arụpụtara si anwụ-mgbatị. E wezụga nke ahụ, a kwadebere ha mgbochi bi na antifriction.

Mpaghara ịkwụ ụgwọ pụrụ iche na bushings, nke akara mkpuchi pụrụ iche nwere mgbanaka mgbanaka na-egbochi mgbapụta, na-enye ohere ị ga-enwe nnwere onwe zuru oke ma na-agagharị na bushes, nke kwesịrị ka ịgbanye nrụ ọrụ. N'ụzọ dị otú a, a na-ebelata nsị nke dị n'ime, wee si otú a na-achọpụta arụmọrụ mgbapụta dị oke mma (ma n'okwu olu ma n'ozuzu ya) yana mmanu kwesịrị ekwesị nke mgbapụta na-akpụ akpụ.

Standard ports: M6 thread depth 12 mm.

Nhọrọ “GAS”: G3/8 thread depth 12 mm. Threads are machined on both body sides.

To mount the pump, n.4 M8 screws , with a torque wrench setting fixed at 27±3Nm.

Shaft M7 nut, with a torque wrench setting fixed at 8Nm.

NKWUKWU NKWUKWU  

Tupu ịmalite sistemụ na-aga n'ihu na-aga n'ihu, anyị na-atụ aro ka ị mee ụfọdụ ụzọ dị mfe:

l Check for the direction of rotation of the pump to be consistent with the drive shaft one.

l Check for the proper alignment of pump shaft and motor shaft: it is necessary that the connection does not include axial or radial loads.

l Protect drive shaft seal during pump painting. Check if contact area between seal ring and shaft is clean: dust could provoke quicker wear and leakage.

l Remove all dirt, chips and all foreign bodies from flanges connecting inlet and delivery ports.

l Ensure that intake and return pipes ends are always below fluid lever and as far from each other as possible.

l Install the pump below head, if possible.

l Fill the pump with fluid, and turn it by hand.

l Disconnect pump drain during startup to bleed air off the circuit.

l At first startup, set pressure limiting valves at min. value possible.

l Avoid lower rotation speed than min. allowed with pressure higher than continuous max. pressure.

l Do not start the system at low temperatures under load conditions or after long stops (always avoid or limit load starting for pump longer life).

l Start the system for a few minutes and turn on all components; bleed air off the circuit to check its proper filling.

l Check fluid lever in the tank after loading all components.

l At last, gradually increase pressure, continuously check fluid and moving parts temperature, check rotation speed until you reach set operating values that shall be within the limits indicated in this catalogue.

Mmiri Hydraulic  

Jiri mmanụ dị na mmanụ na-enweghị ihe ọ havingụ basedụ na-enwe ezigbo mgbochi, mgbochi ụfụfụ, antioxidant, mgbochi corrosion na lubricating properties. Fluids kwesịrị isonyere ụkpụrụ DIN51525 na VDMA 24317 wee gafere 11^th ogbo nke ule FZG.

Maka ụdị ndị ọkọlọtọ, ọnọdụ okpomọkụ nke mmiri ekwesịghị ịdị n'etiti -10 ℃ na + 80 ℃。

Mmiri viscosity viscosity ndị a bụ ihe ndị a: