+ 86-18761016003

Farashin GPM3

Kuna nan: Gida >Samfur >Gilashin Gilashin Ruwa >Farashin GPM3

  • /img/cbmw_type_compound_gear_pumps.jpg
  • /upfile/2019/01/22/20190122100727_337.jpg
  • /upfile/2019/01/22/20190122100735_539.jpg
  • /upfile/2019/01/22/20190122100743_526.jpg

CBMW Type Compound Gear Pumps

  • description
  • Siga da hali
  • Our sabis
  • Sunan

CBMW series compound gear pump contains a monopolegear pump and a stable flow diverting valve,supply one main olcircuit and one stable oil circuit for the hydraulic system,also upto international advanced level.With characters:high pressure,high volumetric efficiency,long usage,with overloadprotection,can be widely used in every hydraulic system.

Model CBMW Dimensional Data


Parameters da hali

sigogi

 

CBMW-F11

CBMW-F13.5

CBMW-F16

CBMW-F18

Hijira

ml / r

11

13.5

16

18

The Rated Pressure

MPa

 

18

Matsakaicin matsin lamba

MPa

22.5

Regulating Range

MPa

10-20

Speedaukar Maɗaukaki

r / min

2000

Speed  Range

r / min

1000-2500

Kullum Flow

L / min

5

7

9

12

Oayyukan ku

IBayanan NSTALLATION  

Kafin fara tsarin akai-akai, muna ba da shawarar ɗaukar wasu matakai masu sauƙi:

l Check for the direction of rotation of the pump to be consistent with the drive shaft one.

l Check for the proper alignment of pump shaft and motor shaft: it is necessary that the connection does not include axial or radial loads.

l Protect drive shaft seal during pump painting. Check if contact area between seal ring and shaft is clean: dust could provoke quicker wear and leakage.

l Remove all dirt, chips and all foreign bodies from flanges connecting inlet and delivery ports.

l Ensure that intake and return pipes ends are always below fluid lever and as far from each other as possible.

l Install the pump below head, if possible.

l Fill the pump with fluid, and turn it by hand.

l Disconnect pump drain during startup to bleed air off the circuit.

l At first startup, set pressure limiting valves at min. value possible.

l Avoid lower rotation speed than min. allowed with pressure higher than continuous max. pressure.

l Do not start the system at low temperatures under load conditions or after long stops (always avoid or limit load starting for pump longer life).

l Start the system for a few minutes and turn on all components; bleed air off the circuit to check its proper filling.

l Check fluid lever in the tank after loading all components.

l At last, gradually increase pressure, continuously check fluid and moving parts temperature, check rotation speed until you reach set operating values that shall be within the limits indicated in this catalogue.

 

 

Ruwan Hydraulic  

Yi amfani da ƙayyadaddun ruwan ma'adinai na tushen ma'adinan ruwa masu kyau na rigakafin sawa, rigakafin kumfa, antioxidant, anti-lalata da kaddarorin mai. Ruwa ya kamata kuma ya bi ka'idodin DIN51525 da VDMA 24317 kuma su sami ta hanyar 11.th Farashin FZG.

Ga daidaitattun samfuran, zafin jiki na ruwa kada ya kasance tsakanin -10 ℃ da + 80 ℃.

 

Matsakaicin dankowar ruwa na kinematic sune kamar haka:

Ƙimar da aka yarda

6÷500 cSt

Ƙimar da aka ba da shawarar

10÷100 cSt

An yarda da ƙimar a farawa

<2000 cSt

Iƙwayar cuta
  

SAUKI DA SAURARA!Iyakar imel ɗin da aka keɓance & Kwastomomi na ƙarancin lokacin ragi